Description
This Controller Bundle will allow you to use the GRBL Controller with our High Torque motors.
This controller bundle contains all the hardware that will be required for powering and controlling your CNC Machine Kit.
The cables on this “Large” Bundle are designed for machines of the following sizes:
- 1000mm x 1000mm
- 1000mm x 1500mm
- 1500mm x 1500mm
For smaller machines see our High Torque GRBL Bundle – Small
Specifications:
Controller:
- Arduino UNO Compatible
- 14 digital input/output pins – 6 pins can be used as PWM outputs
- 6 analog inputs
- 16 MHz crystal oscillator
- Operates at 5V
- Recommended input voltage range: 7V to 12V
- Flash Memory: 32 KB (0.5KB used by bootloader)
- SRAM: 2KB
- EEPROM: 1KB
- CNC Shield V3
- Version 3.00
- Supports GRBL V0.8
- 4-Axis support (X, Y, Z, A-Can duplicate X, Y, Z or do a full 4th axis with custom firmware using pins D12 and D13)
- 2 x End stops for each axis (6 in total)
- Uses GRBL as control software
- Power supply: DC 12-36V (No Power Required to the shield in this bundle.)
Power:
- MEAN WELL Power Supply – 24V 350W
- Output Voltage-Channel: 24V
- Output Power: 348 W
- Enclosed Case
- Input Voltage: 90 VAC to 132 VAC/180 VAC to 264 VAC, 240 VDC to 370 VDC
- Output Current-Channel: 14.6A
- Mounting Style: Chassis
- Length: 215 mm
- Width: 115 mm
- Height: 30 mm
- Input Frequency: 47 Hz to 63 Hz
- Unit Weight: 760 g
Cables & Connectors:
- 4 Core Shielded Stepper Cables (For Stepper Motors)
- 1 x 3000mm
- 2 x 5000mm
- 1 x 5000mm
- 2 Core Shielded Signal Cables (For Limit Switches)
- 1 x 2000mm
- 1 x 5000mm
- 1 x 5000mm
- DC Power Cable
- 3mm (To connect Stepper Drivers to Power Supply)
- 1 x 2000mm
- 3mm (To connect Stepper Drivers to Power Supply)
- Stepper Motor adapter modules (CNC Shield to TB6600 stepper motor drivers)
- Direct Plug into the motor driver socket on the CNC shield
- 4 x 200mm
- EStop Cable (For E-Stop)
- 22 AWG
- 1 x 1000mm
- 4 x EDG-4
- 4 x EDG-2 (For Limit Switches + E-Stop)
- Dupont Cables Male to Female 10 Pack (For Limit Switches + E-Stop)
Signal:
- 3 x Limit Switch Kits
- 3 x Micro Limit Switch
- 3 x Limit Switch Plate
- 6 x M3 10mm Cap Head Screw
- 3 x M5 8mm Low Profile Screw
- 3 x M5 Drop-in Tee Nut
- NOTE: The holes in the switch will need to be opened a little (3mm drill bit) to allow for the M3 screw or you can use an M3 tap to cut a thread into the plastic.
- 1 x EStop Switch
- Max Current: 10A
- Max Voltage: AC 660V.
- Rated Load:
- AC: 220VAC/6A, 380VAC/4A, 660VAC/2A
- DC: 440VDC/0.3A, 220VDC/0.5A, 110VDC/1A
- TYPE: N/C
- Withstand Voltage: 2500V /60S
- Temperature: -25°~+55°
- Contact resistance: <25mΩ
Bill Of Materials
Included Parts List/Bill Of Materials:
Description | SKU | QTY |
Arduino(Compatible) UNO R3 with USB cable | US-ELEC-DCCUINO-UNO | 1 |
CNC Shield – No Drivers | US-ELEC-CNC-SHIELD-NODRVS | 1 |
Stepper Driver – TB6600 4A 40V | US-ELEC-TB6600 | 4 |
Stepper Driver Adapter Module | US-ELEC-DRV-ADAPTER | 4 |
Connector Terminal Block – EDG 3.81mm 4T | US-ELEC-EDG-T-381-4P | 4 |
Connector Terminal Block – EDG 3.81mm 2T | US-ELEC-EDG-T-381-2P | 4 |
Power Supply 24V 350W | US-ELEC-LRS-350-24 | 1 |
CNC Cable Pack – Large | US-ELEC-CABLE-CNCPACK-L | 1 |
Emergency STOP Button N/C Switch | US-ELEC-ESTOP | 1 |
Micro Limit Switch Kit with Mounting Plate | US-ELEC-MICRO-KIT | 3 |
Jumper Shunt – Link (12 Pack) | US-ELEC-JUMPER-12PCS | 1 |
Dupont cable Male to Female 20cm 10 pack | US-ELEC-MF-JUMP-10-20 | 1 |
DC Cable 3mm | US-ELEC-CABLE-DC-2C-3MM | 2 |
DC Cable 2 Core | US-ELEC-CABLE-DC-22AWG | 1 |
Resources:
For details on how to wire and configure this controller with your machine, please visit our wiki here
IMPORTANT NOTE:
- NEVER connect or disconnect any wire(s) while power is applied.
- ALWAYS disconnect power before making any connections or disconnections.
- All mains wiring must be done by a qualified electrician or similarly qualified person.
- Cable color may vary.
Reviews
There are no reviews yet.