GRBL Controller Bundle – Large

(1 customer review)

$159.99

The GRBL Controller Bundle contains all the hardware for powering and controlling your  WorkBee, Ox CNC or other CNC machine.

In stock

Description

The Open Source Mechatronics’ GRBL Controller Bundle contains all the hardware for powering and controlling your  WorkBee, Ox CNC or other CNC machine.

The cables on this “Large” Bundle are designed for machines of the following sizes:

  • 1000mm x 1000mm
  • 1000mm x 1500mm
  • 1500mm x 1500mm

For smaller machines see our GRBL Controller Bundle – Small

Bundle Includes (Bill of Materials):

QTY Description
1 Arduino(Compatible) UNO R3 with USB Cable
1 CNC shield v3.00
4 Stepper Driver – DRV8825
1 Fan – 40×40 24V
1 MEAN WELL Power Supply – 24V 350W
4 4 Core Shielded Cable (use for X Axis, Y Axis, Z Axis and A Axis)
3 2 Core Shielded Cable (use for X Axis, Y Axis, Z Axis)
1 DC Power Cable
1 Ground Wire
4 4 Pin Dupont Wire
3 2 Pin Dupont Wire
4 Terminal Block (5 Pole)
3 Terminal Block (2 Pole)
1 E-Stop Switch + E-Stop Cable
3 Limit Switch Kits

More Details:

Controller: The Controller comes is made up of the following items:

  • Arduino UNO Compatible
    • 14 digital input/output pins – 6 pins can be used as PWM outputs
    • 6 analog inputs
    • 16 MHz crystal oscillator
    • Operates at 5V
    • Recommended input voltage range: 7V to 12V
    • Flash Memory: 32 KB (0.5KB used by bootloader)
    • SRAM: 2KB
    • EEPROM: 1KB
  • CNC Shield V3
    • Version 3.00
    • 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
    • 2 x End stops for each axis (6 in total)
    • Uses GRBL as control software
    • Power supply: DC 12-36V
    • Interface: mini-USB
    • Maximum stepper motor current: less than 2A 2 phase 4 wire stepper motor
    • Over 1A stepper motors must use heat-sinks and/or other cooling (fan)
  • DRV8825 Stepper Drivers
    • Low RDS (ON) outputs
    • Automatic current decay mode detection / selection
    • Internal UVLO
    • Mixed with slow current decay modes
    • Synchronous rectification for low power dissipation
    • Crossover-current protection
    • Thermal shutdown circuitry
    • 3.3 and 5 V compatible logic supply
    • Ground Fault Circuit
    • Load short-circuit protection
    • Six microstepping modes: full, 1/2, 1/4, 1/8, 1/16 and 1/32
  • Fan – 40x40mm 24V
    • Dimensions: 40mm (L) x 40mm (W) x 10mm (H)
    • Rated Voltage: 24V
    • Current: 0.10A
    • Input Power: 0.84W
    • Nominal Speed: 6000 RPM
    • Air Flow: 5.75 CFM
    • Noise: 24 dBA
    • Wire Length: 250mm
    • Connector: 2pin 2.54mm

Power:

  • MEAN WELL Power Supply – 24V 350W
    • Output Voltage-Channel: 24 V
    • Output Power: 350.4 W
    • Enclosed Case
    • Input Voltage: 90 VAC to 132 VAC/180 VAC to 264 VAC, 240 VDC to 370 VDC
    • Output Current-Channel: 14.6 A
    • Mounting Style: Chassis
    • Length: 215 mm
    • Width: 115 mm
    • Height: 30 mm
    • Input Frequency: 47 Hz to 63 Hz
    • Unit Weight: 760 g

Cables & Connectors:

  • 4 Core Shielded Stepper Cables terminated at one end with JST SM 4P (Connector to Stepper Motors):
    • 1 x 3000mm
    • 2 x 4500mm
    • 1 x 4750mm
  • 2 Core Shielded Signal Cables terminated at one end with JST SM 2P:
    • 1 x 1500mm
    • 1 x 4500mm
    • 1 x 4750mm
  • DC Power Cable
    • 22 AWG
    • 1 x 500mm
  • Ground Wire 
    • 20 AWG
    • 1 x 500mm
  • Stepper Cables (CNC Shield to Connectors)
    • Dupont Female Connector at one end
    • 4 x 300mm
  • EStop Cable
    • 22 AWG
    • 1 x 1000mm
  • 4 x Terminal Block 5 Pole
  • 3 x Terminal Block 3 Pole

Signal:

  • 3 x Limit Switch Kits
    • 3 x Micro Limit Switch
    • 3 x Limit Switch Plate
    • 6 x M3 10mm Cap Head Screw
    • 3 x M5 8mm Low Profile Screw
    • 3 x M5 Drop-in Tee Nut
    • NOTE: The holes in the switch will need to be opened a little (3mm drill bit) to allow for the M3 screw or alternatively you can use a M3 tap to cut a thread into the plastic.
  • 1 x EStop Switch
    • Max Current: 10A
    • Max Voltage: AC 660V.
    • Rated Load:
      • AC: 220VAC/6A, 380VAC/4A, 660VAC/2A
      • DC: 440VDC/0.3A,  220VDC/0.5A, 110VDC/1A
    • TYPE: N/C
    • Withstand Voltage: 2500V /60S
    • Temperature: -25°~+55°
    • Contact resistance:  <25mΩ

Wiring Schematic:

IMPORTANT NOTE:

NEVER connect or disconnections any wire while power is applied.
ALWAYS disconnect power before making any connections or disconnections.

Failure to do the above will result in damage to the stepper drivers.

Software:

Links:

Note : Any Mains power connections must be installed by a Licensed electrician or suitability qualified person.

Additional information

Weight 2.3 kg
Dimensions 25 × 25 × 10 cm

1 review for GRBL Controller Bundle – Large

  1. Harry

    Great product!

Add a review

Your email address will not be published. Required fields are marked *